Home > Error Code > Calspa Oh Error Code

Calspa Oh Error Code


Pull only on the crimp connector not the wire. THE PUMP AND MOTOR WAS REPLACED 11 MONTHS AGO AND IT HAS WORKED FINE UNTIL NOW AnswerMichael, You are most likely getting an "OH" code because the control box does not If hit pump button and spa has not cooled off nothing happens.3. Please try again later. http://iembra.org/error-code/code-26530-error-code-00011.php

SE = Spa operating in Standard-in-Economy Mode. I think I got it now. Water got up to 108 and shut off again. If you still have continuity even when the pump is off, then you just need to change the pressure switch out. Ask Your Own Pool and Spa Question Customer: replied4 http://www.hottubworks.com/blog/spa-hot-tub-error-codes-oh-ohh-omg/

Coleman Spa Oh Error

One sensor has detected 110°F. Customer Support Find a Dealer Find an Authorized Servicer Request a Quote Trade in Value Warranty Information Owner's Manuals Find Replacement Parts Maintenance & Care Troubleshooting Water Maintenance Testimonials Contact Customer Yesterday I put the spa on continuous filter cycle.

I cannot thank you enough for your help. This is a pressure switch?Customer: hang on I will pull off the control panel cover to check that.poolguy810 : yes, the pressure switch just senses water flow, so we don't need FLO* = Flow Switch (heater is deactivated. Cal Spa Dr Error Code thanks for your help RB Share this post Link to post Share on other sites uptonogood 0 Newbie Members 0 8 posts Posted December 15, 2010 · Report post There

No action is necessary. Cal Spa Blinking Oh Contact qualified service technician. If you're going up to 108 degrees in the spa, then the most likely cause is your temp sensor, this is primarily what controls how hot the spa is allowed to https://spacare.com/commonspasideerrorcodes.aspx In most cases overheat issues are related to the relays on the circuit board, or the temp sensor has failed and will need to be replaced.

Press Temp again to cycle through the options until the display reads "FC". Hot Tub Error Code Oh You can also check the pressure switch or flow switch with a an Ohm meter. If you put a new filter in, this is not the issue, it is most likley the pump if you are sure nothing else is restricting the flow of water. balboawatergroup 6,018 views 2:47 How To Make a FLOATING HOT TUB - Duration: 4:33.

Cal Spa Blinking Oh

The heat vessel will start to boil like a kettle on a stove. http://www.poolspaforum.com/forum/index.php?/topic/26941-oh-error-code/ Spa has shut down. Coleman Spa Oh Error It's easy! Cal Spa Hh Error Code Note: The control system brand name is usually different from the hot tub brand name.

Recently changed This answer was rated: ★ ★ ★ ★ ★ I am getting the OH display on my Calspa. Get More Info Pretty quick goes to OH and shuts down.2. Sensors don't fail very often. When water doesn't flow fast enough through the heater, it removes less heat, and the temperature of the water increases. Cal Spa Lf Error Code

If the control panel indicates "SN" right after the breaker is reset and the self-test completes you will need to replace the sensor set or the circuit board. If you don't want to go to your local dealer you can find the pumps several places online. In an emergency situation you can drain the tub as completely as possible. useful reference If you have multiple pumps it is most likely the top plug.

One sensor has detected 118° F at heater. Cal Spa Error Codes The first thing you want to do before doing anything else is shut the spa down, remove the filter and make sure all the jets are open. All Rights Reserved.

If the water temperature is below 104 you can turn the heater on simply BY raising the set temperature to 104 degrees.

After pump has been running for 2 minutes temperature will be displayed.breadcrumb breadcrumb 2. If the display shows only this message (periodically blinking), the spa is shut down. Share this post Link to post Share on other sites wherman 0 Newbie Members 0 7 posts Posted December 11, 2010 · Report post Had a similiar problem, if the Cal Spa Temperature Sensor Location Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off.

Spa Overheating Troubleshooting Flow Chart Here's a Cal Spa troubleshooting flow chart that has some other possible triggers of seeing OH, OHS, OHH or HH blinking on your spa panel. The codes above are all related to flow issues or the pressure switch/flow switch and are the most common error codes. Water temperature has reached 118°F. http://iembra.org/error-code/code-16000-error-code-00018.php ehowathomechannel 116,178 views 3:08 How to Replace Sundance Spas Circulation Pump - Duration: 6:01.

Beginning with the 2014 product line, Cal Spa control panels display different message codes. So since you're still heating, that's a good thing, but down the road some time you may end up replacing the board, but I wouldn't get in to that until you It was dirty enough to impede water flow which would cause an overheat. JustAnswer.com...has seen a spike since October in legal questions from readers about layoffs, unemployment and severance.

Open the spa cover and let the spa cool down for 10 minutes, then touch the control panel to reset the circuits, or push a red reset button on air systems. SpaDayz 13,486 views 5:41 Intex pure spa review and problems. - Duration: 5:21. The main reason is water flow through the spa control system, if water is not flowing at a rate to satisfy the pressure switch, it will result in one of the I specialize in electrical questions and I am most familiar with spas that were manufactured by NEMCO, Regency, Hydro Spa, Gulfcoast Spas, Leisure Bay, and Premium Leisure.

This is known to cause OH because its reading the temp of the equipment area & if you live in the southern US your compartment temps are much higher than the Both are secured with black plastic nut around the gray cable. If the water continues to boil after you unplug the pump and unplug a wire from the pressure switch you most likely have a bad circuit board with a stuck heat Credentials confirmed by a Fortune 500 verification firm.

If you hear the heat relay click off and the boiling subsides after you remove a wire from the pressure switch...replace the pressure switch. Loading... We have milder weather here today and I am off work so I plan to check the pumps for clogs. The "OH" error is most often caused by a stuck pressure switch or a stuck heat relay on the circuit board.