Cal Spa Oh Error Codes
I'm looking forward to asking you questions in the future. Ask an Expert Home Improvement Questions Pool And Spa Repair How JustAnswer Works: Ask an Expert Experts are full of valuable knowledge and are ready to help with any question. Sundance Spas ILOC = Interlock failure - possible pump or ozone spike FLO = Pressure switch malfunction or Flow switch malfunction (system specific) Hold = Panel buttons pressed to many times Clean or replace the spa filter, open all the jets and turn the pump on high. this content
The hi limit sensor that throws up the OH code is mounted right on the heater, so if it were the heater itself that was overheating and not the spa water, I liked that I could ask additional questions and get answered in a very short turn around. So check this out and hopefully you can resolve it by just replacing the filters. Spa Overheating Troubleshooting Flow Chart Here's a Cal Spa troubleshooting flow chart that has some other possible triggers of seeing OH, OHS, OHH or HH blinking on your spa panel. Get More Information
Cal Spa Hot Tub Error Codes
Now if your pressure switch is stuck that senses the water flow, then yes, that would be a possibility. Reset the breaker and leave the filters out temporarily while you troubleshoot. Scott Felsen 354 views 0:49 testing and replacing or servicing a hot tub or pool recirculating pump - Duration: 8:06.
This feature is not available right now. GP Hesperia, CA I couldn't be more satisfied! Once again these can be caused by a flow issue. Cal Spa Error Codes Sign in to make your opinion count.
I will have to wait till better weather to take the cabinet apart and see what I can find, I am beginning to thinks it may be the motor or pump Cal Spa Hh Error Code The wires you removed are correct, so the heater is not causing the breaker to trip.Customer: so the sensor wires are not is a plug of 4 black and red wires?TheHotTubGuy Customer: okay give me a minuteCustomer: I made sure the sensor is seated correctly and flipped the fuse and it pops the breakerTheHotTubGuy : Was it popping the breaker BEFORE we Did you have some freeze damage...you mentioned a cracked heater union which is a classic sign on the CalsCustomer: I thought it might be a lack of water for the OH
Ask an Expert Home Improvement Questions Pool And Spa Repair How JustAnswer Works: Ask an Expert Experts are full of valuable knowledge and are ready to help with any question. Balboa Hot Tub Error Codes OH, OHH, OHS, OHt, HL, HiLi, Sn2, Sn3, tS, Ht, Blinking Lights Temperature Sensor Failure. thanks for your help RB Share this post Link to post Share on other sites uptonogood 0 Newbie Members 0 8 posts Posted December 15, 2010 · Report post There If the water temperature is below 104 you can turn the heater on simply BY raising the set temperature to 104 degrees.
Cal Spa Hh Error Code
Send Share This Copyright © 2016. SpaDayz 16,260 views 7:49 How to repair hot tub error code SN3 - Duration: 17:46. Cal Spa Hot Tub Error Codes So first try running the spa on low speed without the filters to see if you still get the OH code to come up. Cal Spa Lf Error Code SN, Sn1, Sn2 Sn3, HL, E1, E3, Prh, HtS, Blinking Lights Hi Limit Sensor Failure.
I fix those had the tub going back to 100 degrees and drained today the tub cleaned it and replaced the left side heater union that was cracked. news Spa has shut down. Thank you so much!!!! Alex Los Angeles, CA Thank you for all your help. Hot Tub Error Code Oh
What Customers are Saying: You did one super job of explaining to me everything there is to know about this fridge. Sounds like it could be one of several things. Water got up to 108 and shut off again. have a peek at these guys The temp sensor is the larger of the two silver bullets.
thanks , Share this post Link to post Share on other sites uptonogood 0 Newbie Members 0 8 posts Posted December 17, 2010 · Report post Ok heres an update Cal Spa Error Code Dr PRA7 Reviews 134,034 views 5:08 FLO Error Code - Duration: 0:43. Someone removed 1 sensor wire from the harness for some reason.
Once you know the heater is operating, identify the pump plug.
Make sure that small hi limit sensor bulb is inserted into the heater tube behind that metal spring clip. Again I do understand where your coming from all the problems and I believe any of my issues have been from the guy that "thought" he was a hot tub repair saleenandlance 34,739 views 5:21 Sundance Spas ~Flow Switch Repair w/Cheap Hardware Store Parts ~Altamar 2001 - Duration: 7:49. Hot Tub Overheating Troubleshooting Recently changed out the water and cleaned the filter about a month ago.
Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off. What else should I check on while I have it open?Thx Scott Share this conversation Expert: poolguy810 replied4 years ago. TURN OFF THE BREAKER BEFORE SPRAYING THE RELAYS WITH CONTACT CLEANER. check my blog I wanted to relay something that may be important.
Sign Up All Content All Content This Topic This Forum Advanced Search Browse Forums Blogs Calendar Staff Online Users More Activity All Activity Search More More More All Activity Home Hot stackz00 146,018 views 8:06 History in a Hot Tub (WK 247.4) | Bratayley - Duration: 19:16.