Home > Error Code > Cabrio Top Load Washer Error Codes

Cabrio Top Load Washer Error Codes


Lid lock/switch assembly F7 E1 Basket speed sensor fault See if the spin basket rotates freely. The main electronic control board will usually need to be replaced to fix this failure. You can also search forowner’s manuals, get troubleshooting advice from an expert and findwashing machine replacement parts. For repair how-to help, visit the PartsDirectrepair helpsection, which includes repair help for washing machines, other major appliances, lawn and garden equipment, garage door openers, vacuum cleaners and more. weblink

May not be used with any other coupon, associate discount, or during Family & Friends or Member events. Always measure detergent and follow detergent directions. Water valve assembly F0E5 Off balance load Distribute items evenly when loading. However, in this wasteful world of poor quality the inner tub may be jammed in the down position, unable to float off the drive hub because of a rusted drive shaft!

Whirlpool Cabrio Washer Error Code F5

The washer has attempted to fill and begin a wash cycle. Back to top Error codes in front load washers F8 E1 or LF or LO FL Error Code in Display Was this article helpful?YesNo Recommended articles There are no recommended articles. Cabrio HC Error Hot & Cold Hoses Switched This code will appear at the end of the wash cycle to indicate that the hot and cold-water inlet hoses are reversed.

Check the drive motor wiring. If the inlet water valve assembly is defective, replace it. If the problem persists, replace the main electronic control board. Cabrio Washer F3 E1 That component has the optical tachometer.

Washer Diagnostic Modesand Tests Cabrio uL Error Unbalanced Load If the load is unbalanced, the Cabrio washer will display this code while running an imbalanced load correction routine at the end Whirlpool Cabrio Error Codes E1 F3 Drive motor, wire harness, main electronic control board F7E3 The clutch engaged the spin basket during the wash cycle The clutch should only engage the spin basket during the spin cycle. Drive motor F7 E7 Motor is unable to reach target RPM Rotate the spin basket to see if it spins freely. http://www.searspartsdirect.com/washer-repair/error-codes/whirlpool-cabrio-top-load-washer-error-codes.html NOTE: Both Hot and Cold water must be supplied to the washer.

Sign up here Shop Your Way members get $10 in points on any PartsDirect purchase with coupon code SYW10. Whirlpool Cabrio F50 If the washer isn’t filling, check the water supply faucets behind the washer to make sure that they are fully open. If the load cannot be balanced by that routine, then uL will flash and the door will unlock. Check the washer drain and the drain hose for clogs or restrictions.

Whirlpool Cabrio Error Codes E1 F3

Main electronic control board, User interface control F3 E1 Water level pressure sensor fault Unplug the washer.

Suspension rods/springs F1 E1 Main electronic control board failure Unplug the washer. Whirlpool Cabrio Washer Error Code F5 It should measure about 50,000 ohms at 77 degrees. Cabrio F50 Error Code Working...

Try to manually unlock the washer lid without breaking the lid lock/switch assembly and the lock strike. have a peek at these guys Learn More for questions or assistance, call 1-800-252-1698 (Se Habla Español) M-F6:30 a.m. - 10:30 p.m. User interface control F2 E3 Mismatch of main electronic control board and user lnterface control This code is for models with a digital display. Remove any obstructions between the spin basket and tub. Code F50 Cabrio Washer

Replace the wire harness if damaged. By accepting Shop Your Way member benefits and offers, you agree to the Shop Your Way terms and conditions, available at www.shopyourway.com/terms. If so check pressure hose connection to machine/motor control.Ld(F32)Long DrainLd flashes when the water level does not change after the drain pump is on.Is the drain hose or the drain pump check over here If the components are damaged, replace them.

Cabrio Washer Diagnostic Modesand Tests Cabrio Sd Error Suds Detected (Stored Error Code F71) Did you use regular detergent? Washer Code F51 If the basket spins freely, unplug the washer and check the wire harness connections between the RPS and the main electronic control board. Please check back in a few minutes.

Check the wiring connections on the main electronic control board in the console.

Sign up here Shop Your Way members get $10 in points on any PartsDirect purchase with coupon code SYW10. Drive system components Back To Top Click to Chat We're available to chat FAQs Check out the most frequently asked questions Video How to use the site (3:58) fast shipping Sears Valid for standard ground shipping within the continental United States and not valid for shipments to Alaska, Hawaii, Puerto Rico, Guam and the US Virgin Islands. Cabrio Washer Error Codes F1 The panel also lights up like a Christmas tree when there is a problem.

Open the console and check the wire harness connection between the main electronic control board and the user interface control board. OK, Continue Like ApplianceAssistant on Facebook! Working... this content User Interface control F2E5 User interface failure Unplug the washer and replace the user interface control.

To return a part, you must first obtain a Return Authorization number by calling 888-205-0966 or visiting our website at www.SearsPartsDirect.com and chat with a Parts Trusted Advisor. If the thermistor is defective, replace it. Check for weak suspension springs. Inlet water valve wiring harness (this harness includes the thermistor) F5 E1 Lid switch fault This code is displayed if Start is pressed with the lid open.

Lift the top panel of the washer to access the lid lock/switch assembly. If the motor is defective, replace it. Remove several items and add HE detergent. This can be caused by excessive friction in the drive system.

Let the suds dissipate and then drain the washer. Check to see if the water drained out. Sign in 78 Loading... Open the lid and spin the impeller inside the basket.

If not, run the drain cycle routine to evacuate the water. Lid lock/switch F5E3 Lid won't unlock Unplug the washer.